NMRA Hot Street/NMCA Pro Stock/All Motor N/A 800hp+++ Engine/ Turn Key/359ci

359ci Naturally Aspirated Race Engine
Engine built by Mike Curcio of MCRP is being sold turn key with only 7 passes since being freshened with new rods, pistons, and rings. This engine is fresh off the dyno and made just over 807 hp with C25 and 829 hp with Q16! Listed are a few specs and will release all other specs for serious buyer.

Small Block Ford:
*359 ci 8.7 deck SVO Block
*Bronze Lifter bores
*Jesel keyway lifters
*Roller cam bearings
*Huge NA solid roller Cam (specs to buyer)
*Edelbrock Glidden Victor Heads with all Titanium Valves (specs to buyer)flows 389 cfm @ 1.00 of lift
*Fully Ported by hand Super Victor Intake manifold
*Jesel Belt Drive
*GRP Pro Stock Rods
*LA Billet Crank
*Patterson Pistons
*Manton Pushrods
*Jesel Rockers/stands (mowhawk)
*Sheetmetal Valve covers
*Bob Book Racing Custom Hot Street 4150 carb with 1.5 " wilson manifolds 4 hole spacer.
*CSR polished water pump
*front motor plate un-cut
*custom stock car single stage oil pump (belt drive)
*Moroso 4 vane vacuum pump (belt drive)
*Moroso ultra 40 race wires
*MSD crank trigger

Engine is being sold turn key with all lines and fittings!

Also to be included:
- 7" Dynamic (Lupo) Converter match for this engine - 7900 stall
- extra ported 8.7 edelbrock intake manifold- (welded)
- Custom Steel Headers (no collectors)
- 2" HVH 4 Hole spacer
- 55 mm custom bullet camshaft
- extra moroso vacuum pump
- extra MSD Distributor

Current engine with converter has been 8.80's in a 2800lb car with a TH400.

$19 k for everything....

Will separate.
$11K for short block..
$8 k for top end..

1)

*359 ci 8.7 deck SVO Block - 4.155 Bore
*Bronze Lifter bores
*Roller cam bearings
*All machining done $2500

PAID $6000 IN PARTS AND MACHINING

*Jesel Belt Drive $700 - $950 NEW
*GRP 5.900 Pro Stock Rods $1200 - $1750 NEW
*LA Billet 3.300 Crank $1800 - $3200 NEW
*Patterson Pistons for Victor Glidden Heads (lightened by patterson) 4.155 bore $1000 - $1900 NEW

TOTAL FOR EVERYTHING = $6250 will throw in camshaft and pushrods if package is bought = SAVE $1000 OFF INDIVIDUAL PRICE.

2) 7" Dynamic (Lupo) Hot Street - 7900 stall (lightweight internals) - $950

3) 8" Competition Transmission Hot Street - 7000 stall (lightweight - internals)
$900

4) ported 8.7 edelbrock intake manifold for Victor gliddens (not NMRA/NMCA legal) - $500

5) Custom Steel Headers with Kooks stainless merge collectors for Victor Gliddens
$800

6) 2" HVH 4 Hole spacer - $60

7) 2.00" Wilson Shear plate - - $100

8-NMRA Hot Street 55 mm custom bullet camshaft - .974 lift (specs to buyer) - $500

9) 4 vane moroso vacuum pump set-up and pulley - $500

10) SBF MSD Distributor - $180

11) 9 inch ford strange 3RD member with 4.86 pro gear. $1600 (2 runs)

12) 9 inch ford 5.00 gear. $150

13) 1.7 ratio jesel rockers for a victor head set of 8 - new in box $600

14) SBF Scat 4.100 forged crank 3.00 mains (new) - $700

15) SBF CSR polished water pump - make an offer

16) Mike Curcio ported 8.7 edelbrock intake manifold - $1200 - for Victor Glidden - Awesome piece

17) Bob Book 4150 Hot Street Carb. NMRA/NMCA Legal - $1300 paid $1800 new - Dyno time only..